Another Fine Hardwood Furniture Job Done

If you've been following my previous posts, you know that I've been busy building a custom bedroom set.  Well, today the bedroom set left my shop and is on  its journey from  here in  Vermont to its excited owner  in New Mexico.

Shown below is the fully constructed bed.  It's made of some beautiful cherry wood harvested in Pennsylvania and purchased from my local wholesaler.  I hadn't bought such clear, flat lumber in a long time, if ever.  This is my own contemporary-designed arched bed.

Although my camera likes to throw in a little distortion, here is my own design of a contemporary dresser.  My customer wanted a very sleek, simple look and didn't want any drawer pull hardware.  The drawers have a hand-hold routed out of the bottom front edge for easy grasping and operation.

And finally, my custom-designed night table which matches the dresser and compliments the bed.  I made two of these for my customer.

The shipping company did a fabulous job blanket wrapping all of these pieces of furniture and I am very confident that they will make it safely to the western part of the country.

Thanks for reading,
Sue

How I build the custom Contemporary Arched Bed - Part 3

Making the headboard and footboard panels -

After gluing up the the headboard and footboard panels, cutting them to their length and width, I proceed to mill the tenon which will fit the mortise I created in the leg.  The next thing that I did was to lay out and cut the arch on the top of the panel followed by rounding over all the edges of the panel with a 1/4" roundover bit in my router.

Before I can glue the panel to the legs I mill the panel to accept the bed hardware.  The area shown below will house the hardware that accepts the hooks on the ends of the bed rails.  Although the panels are just 3/4" thick, the backside of this area butts into the leg which will allow me to use longer screws to go through the panel and into the leg, providing extra strength in the construction.

Here is the panel all ready to be glued to the legs:

And here is a shot of the panel next to the leg, oriented in the way in which they will be glued together:

Here are photos of the headboard and the footboard in clamps after gluing:

Soon I'll post the final, assembled bed.

Thanks for reading,
Sue

How I build the Custom Contemporary Arched Bed – Part 1

Let’s start with the legs.  As I said in a previous post, the legs of the headboard and footboard are ¾ round “posts”.  The top of the leg will be curved to match the arch in the panel running from leg to leg.  This picture shows a SketchUp rendition of one of the headboard legs and panels:

Here is the lumber for the four legs.  In order for me to be able to turn these legs round on a lathe, they need to be a solid square.  Three boards are grouped together for each leg.  The board on the bottom of the stacks is a little more than half the thickness of the finished leg and its width is a little more than the full thickness of the finished leg.  The remainder of each leg consists of two more square pieces.

One of the two square pieces will be permanently glued to the wide board, becoming part of the final leg, and the other will be temporarily glued in place, making up a full square ready for turning.  After turning the leg round I will remove that piece.  At this point I’ve been careful to orient all of my boards to give me the best looking leg possible in terms of grain and color.

Ok, so how am I going to “temporarily” glue a piece in place and then remove it leaving me a nice, clean, inside square area for my panels?  My method is this – all of these pieces of wood are cut longer than the finished leg; about 5 inches.  So for the temporary piece of wood, I am going to put glue on its last 2” of each end only.  It is the ends that are important for attaching the square to the lathe.  Once I finish turning the leg I will cut off each end past the glue area and the temporary piece will just fall out leaving me a clean interior square area.  The picture below illustrates how the boards will be glued together. (Click on the picture for a larger version.)

Before I can do any of the gluing I have one more thing to do.  The headboard and footboard panels ultimately need to be securely attached to these legs.  The strongest method is to use a mortise and tenon joint.  If I were to glue even the permanent boards together now I wouldn’t have access for my router to cut the mortise.  This is where some very precise layout occurs.  Remember that these boards are extra long.  The first thing I need to do is determine where the final top and bottom of the leg are going to be and mark that on my wood.  The next thing is to strike a line down the length of the wider board where the inside edge of the permanent square will be glued.  Now that I have those marks I can determine where the panel will be positioned and then mark out the mortise.  This result is shown below.  (Click on the picture for a larger version.)

Coming soon in Part 2 - Cutting the mortise, gluing up the pieces, mounting on the lathe and turning.

Thanks for viewing,

Sue

Stay Tuned...

As you might see in a previous post, I am currently working on building a custom designed bedroom set.  The bed is actually one that I originally designed oh, about a year and a half ago for a different client.  I'll be posting some informational photos and text of how I actually build that bed.  The legs are 3/4 round "posts" with the headboard and footboard panels tenoned into those legs.  It's all about planning and layout (as is true with all woodworking).  Doing steps in a certain order is important in order for it all to fit together.  So stay tuned for watching me put all of the steps together!

See a photo of the original bed I built.

Sue